AC INC Roofing

Ice Dams and Commercial Roof Flashing Leaks

Understand how ice dams and freeze-thaw cycles cause flashing failures on commercial roofs in Colorado. Prevention tips and repair from AC INC. Roofing.

Ice Dams and Commercial Roof Flashing Leaks

Commercial buildings across Denver, the Front Range, and Cheyenne face a unique winter challenge: ice dams and daily freeze-thaw cycles that stress roof flashing and create leaks. If water only appears during sunny winter afternoons or right after a thaw, flashing at walls, edges, and penetrations is a likely culprit.

Why winter targets flashing on commercial roofs

Flashing is the protective detailing at roof perimeters, walls, curbs, penetrations, and transitions. In winter, it’s subjected to:
– Freeze-thaw movement: Daily swings above/below 32°F expand and contract metals, membranes, and sealants, opening gaps at laps and terminations.
– Ice dam pressure: Refreezing around scuppers, drains, and gutters forms dams that back water up and under flashing.
– Snow load and drift: Snow piled against parapets pushes meltwater into vertical seams and corner details.
– UV and wind: High-altitude UV in Colorado and Chinook-driven winds accelerate sealant aging and can loosen fasteners at counterflashing and edge metal.

Where ice dams cause leaks first

Commercial low-slope systems (TPO, EPDM, Modified Bitumen, BUR, coated roofs) and metal roofs most often leak at:
– Parapet and roof-to-wall flashing (insufficient height, loose term bars, missing cover strips)
– Edge metal and coping (back leg too short, fasteners backing out, separated splice plates)
– HVAC and skylight curbs (improper corner reinforcement, split welds, aged mastics)
– Pipe/penetration flashings and old pitch pans (shrunken boots, cracked pourable sealant)
– Scuppers, gutters, and downspouts (ice choking outlets, separated seams)
– Drains and sumps (ponding/slush refreezing at strainers, compromised clamp rings)
– Expansion joints and transitions (bridging and shrinkage at movement points)

Colorado/Front Range factors that amplify damage

  • Rapid temperature swings and Chinook winds cause repeated thermal cycling in a single day.
  • High UV exposure at altitude ages elastomers and mastics faster than in lower-elevation markets.
  • Wind-driven snow and 2″ hail common to the Front Range can pre-damage seams, laps, and protective granules, setting the stage for winter leaks.

Red flags of flashing failure in winter

  • Leaks that appear only during daytime thaw or sunny afternoons
  • Staining or bubbling paint on interior parapet walls or below roof-to-wall areas
  • Ice stalactites at scuppers or under coping/edge metal
  • Membrane pulled down from walls, exposed termination bars, or loose counterflashing
  • Granule loss around Mod Bit laps or alligatoring mastics at details
  • Rust trails and backed-out fasteners along metal edge or coping joints

What to do when you have a winter leak

  • Protect people and property: place buckets, move equipment, and mark wet areas.
  • Do not chip ice on the roof—this damages membranes and edge metal.
  • Note when the leak starts and stops (during thaw, near a specific wall, after sun exposure) and take photos; timing helps pinpoint the flashing detail.
  • Call a licensed commercial roofer for a safe, documented inspection and temporary repair.

AC INC. Roofing provides free roof inspections by Master HAAG-Certified inspectors and offers repair and replacement for commercial systems across the Denver metro, Front Range, and Cheyenne.

Prevention: design, materials, and maintenance that work

Design and detailing best practices (per NRCA/IBC)

  • Maintain adequate flashing height: typically 8″ minimum above finished roof at walls and curbs to clear snow and refreeze zones.
  • Use termination bars with compatible cover strips on membrane turn-ups; avoid exposed fasteners where possible.
  • Reinforce inside/outside corners and curb corners with pre-formed accessories or additional plies.
  • Ensure continuous counterflashing with proper laps; seal and secure splice plates at coping joints.
  • Provide overflow pathways (overflow scuppers or secondary drains) to reduce backup pressure if primaries ice over.
  • Keep scuppers, gutters, and drains clear before storms; confirm positive slope to drains and unblocked strainers.

System-specific considerations

  • TPO/EPDM/Modified Bitumen: Watch for membrane shrinkage at perimeters, split welds, and aged mastics. Add/re-weld cover strips over term bars; repair or replace failing corners and boots.
  • Metal roofs: Thermal movement can open joints at curbs and end laps. Replace failed butyl tapes, tighten/replace fasteners with sealing washers, and ensure snow/ice doesn’t block eave drainage.
  • Fluid-applied coatings: Great for extending service life when details are properly reinforced. Pay special attention to fabric-reinforced corners, penetrations, and seams before coating.

Maintenance cadence for Colorado winters

  • Fall (pre-snow): Comprehensive inspection with photos and a punch list for flashing repairs, drain/scupper cleaning, and edge metal fastening checks.
  • Mid-winter: Post-storm checks for ice-related displacement at coping, curbs, and scuppers when safe to access.
  • Spring: Evaluate for UV and hail damage, renew sealants, and plan restorative work such as fluid-applied coatings or targeted flashing replacement before summer storms.

When restoration or replacement is smarter

Not every ice-dam leak needs a full replacement. In many cases AC INC. Roofing can:
– Execute targeted flashing repairs at walls, curbs, scuppers, and edge metal
– Install or renew compatible cover strips and corner reinforcements on TPO/EPDM/Mod Bit systems
– Apply fluid-applied coatings (where appropriate) to extend service life and add redundancy at details
– Replace worn coping/edge metal with properly detailed systems

If hail or wind has contributed to flashing or membrane damage, our team specializes in storm-damage evaluation and insurance claims support, providing thorough documentation to help owners and managers navigate the process.

Why facility managers choose AC INC. Roofing

  • Credentials you can verify: Colorado’s first company to reach Master HAAG Certification; Atlas Pro+ Platinum Certified; GAF Certified; Directorii-certified (backed by up to $20,000 customer guarantee); Fortified Roofing Solutions certified for enhanced resilience.
  • Commercial expertise: Repairs, replacements, and restoration on TPO, EPDM, Modified Bitumen, metal, tile, and fluid-applied systems.
  • Integrity and documentation: Clear inspection reports, photos, and scope of work. Our focus is integrity, reliability, and exceptional service.
  • Local and licensed: Based at 6145 Broadway, Suite 25, Denver, CO 80216. Serving the Denver metro, Front Range, and Cheyenne, Wyoming.

Getting ahead of next winter

A proactive flashing survey before the first hard freeze can prevent the vast majority of ice-dam leaks. If you manage one building or a portfolio, we can set up seasonal inspections and a prioritized plan for repairs or restoration tailored to Colorado’s climate.

Have an active leak or want a pre-winter inspection? Contact Us today.

Roofing blog

Request a free roof inspection · Call (303) 550-4530 · Get an instant estimate